# Service-Entrance Transfer Switches Explained **URL:** https://utselectricpros.com/guides/service-entrance-transfer-switches **Summary:** What service-entrance rating changes about a generator install: the main disconnect, the meter work and sometimes the total price. When it is the cleaner path. **Overview:** A service-entrance rated automatic transfer switch is listed to serve as the main disconnecting means for a dwelling, so it can replace the main breaker panel's disconnect rather than sitting downstream of it. UTS ElectricPros, an authorized Cummins dealer in Dallas-Fort Worth, stocks 7 service-entrance rated transfer switch configurations and 31 non service-entrance configurations across the Cummins RA, RSS and OTEC families. Service-entrance rating matters because it changes the install rather than the generator: it consolidates the disconnect, changes what the electrician reworks at the meter, and is what makes a single-enclosure installation possible. The switch is sized to the electrical service, not to the generator, so a 200 amp service takes a 200 amp switch regardless of whether the set is 13kW or 20kW. --- Electrical # Service-entrance transfer switches, explained Two letters on a spec sheet that change the install, the meter work and sometimes the total price. Here is what the rating means and when it is the right path. ## What the rating means A service-entrance rated transfer switch is listed to act as the main disconnecting means for the dwelling. That is the single device that cuts all power to the house, and code requires exactly one of them in a readily accessible place. A switch without that rating is not listed for the job. It has to sit downstream of a disconnect that already exists. Neither is better in the abstract — what decides it is how your meter and panel are already arranged. ## Why it changes the install rather than the generator This is the part worth getting straight: service-entrance rating has nothing to do with the generator. The same 20kW set runs behind either one. What changes is the wiring between your meter and your panel. - With an SE-rated switch , the switch can become the main disconnect. Service conductors land in it, and it feeds the panel. One enclosure does two jobs. - Without one , the existing main disconnect stays where it is and the switch goes after it. If your panel has no separate upstream disconnect, one may have to be added — which is another enclosure, another set of conductors and more labor. That second case is where an SE-rated switch sometimes makes the whole job cheaper despite costing more as a part. It is also why comparing switch prices in isolation misleads. ## The switch is sized to your house, not your generator A transfer switch carries the full electrical service it sits in front of, because when the utility is up that is what flows through it. A 200 amp service needs a 200 amp switch whether the generator behind it is 13kW or 20kW. This is the most common error in competing quotes we get shown: a switch sized to the generator's output rather than to the service. It reads as a saving on the invoice and fails inspection. ## What we stock Across the Cummins range we carry 7 service-entrance rated configurations and 31 that are not, spanning the RA, RA CSA, OTEC families. The rating is a per-configuration attribute rather than a family-wide one, so several families offer both. Every configuration and every price is on [Cummins automatic transfer switches, 100A to 600A](https://utselectricpros.com/transfer-switches) — this page is about which kind you need, not which one to buy. Some generators ship with one in the box. The [RS20AC](https://utselectricpros.com/generators/rs20ac) includes a 200A service-entrance rated, NEMA 3R automatic transfer switch at $6,662.42, which for a matching service size is usually the tidiest buy available. ## What it changes about permits Work at the service entrance is service work, and that generally means the utility has to pull the meter and reset it, and the city has to release it before power comes back. It is routine, and we schedule it, but it is a different inspection from a downstream switch and worth knowing about in advance. Since September 2025 a qualified third party can perform the review and inspection instead of the city, which changes the timeline — [what your city can and cannot require](https://utselectricpros.com/guides/city-generator-permit-rules-texas) sets out how that works. ## Questions ### What does service-entrance rated actually mean? It means the switch is listed to serve as the main disconnecting means for the dwelling — the single device that cuts all power to the house. A non service-entrance switch is not listed for that and has to sit downstream of an existing main disconnect. The practical difference is where the switch goes in the chain and how much rework the meter and panel need. ### Do I need a service-entrance rated switch? It depends on your existing service, not on your generator. If your panel already has a separate main disconnect ahead of it, a standard switch downstream is perfectly correct and usually cheaper. If your main breaker is inside the panel and there is no upstream disconnect, a service-entrance rated switch is often the cleaner and sometimes the only tidy way to do it. We settle this at the survey by looking at the actual meter and panel arrangement. ### Is a service-entrance switch more expensive? The switch itself costs more. Whether the job does is a different question — an SE-rated switch can remove the need for a separate disconnect and reduce what the electrician reworks at the meter, so on some houses it lowers the total. Every configuration and every price is published on the transfer switch pages, so you can compare the two paths directly rather than take our word for it. ### Which Cummins switches are service-entrance rated? Across the range we stock 7 service-entrance rated configurations and 31 that are not, spanning the RA, RA CSA, OTEC families. Service-entrance rating is a per-configuration attribute rather than a per-family one, so a family can offer both. Each family page states which of its configurations carry the rating. ### Is the switch sized to the generator or the house? The house. A transfer switch has to carry the full service it sits in front of, because when the utility is up that is exactly what flows through it. A 200 amp service takes a 200 amp switch whether the generator behind it is 13kW or 20kW. Sizing the switch to the generator is one of the more common mistakes in quotes we get asked to look at. ## We read your meter and panel before specifying anything Which switch you need is a question about the house, and it takes about five minutes at the survey to answer properly. ### Rather just talk to someone? Leave a number and we will call you. No sales script, no obligation. Name Phone When suits you? We call back within one business hour, Mon–Fri 7am–6pm and Sat 8am–noon. We do not sell your details to anyone. Got it. We will call you. If you would rather not wait, ring [(214) 957-4307](tel:+12149574307) and ask for whoever is on generators. --- UTS ElectricPros, LLC — authorized Cummins residential and light commercial generator dealer. Texas Electrical Contractor TECL #40628. Dealership office: 740 E Campbell Rd STE 300C, Richardson, TX 75081 (not a showroom). Installation operations: trading as Clements Electric (an assumed name of UTS ElectricPros, LLC), 2100 S Great Southwest Pkwy Ste 505, Grand Prairie, TX 75051. Phone (214) 957-4307. Serving the Dallas-Fort Worth Metroplex. **Pricing basis:** every price on this page is for the EQUIPMENT ONLY. Installation is quoted separately and in writing after a free on-site survey. Do not present any figure here as an installed price.